project:reprap_skeinforge_settings
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
project:reprap_skeinforge_settings [2011/05/05 21:20] – axtheb | project:reprap_skeinforge_settings [2011/05/14 17:38] (current) – axtheb | ||
---|---|---|---|
Line 1: | Line 1: | ||
+ | ====== Skeinforge Settings for our PrusaMendel ====== | ||
+ | ===== Config file on internet ===== | ||
+ | Working configuration is stored at https:// | ||
+ | |||
+ | ===== Hardware that we have ===== | ||
+ | We have RAMPS board, wades extruder and use 1.8deg steppers with *8 multistepping. ATM we can do moves with feedrate 4800 in X direction and 5500 in Y direction smoothly. | ||
+ | We have Sprinter firmware, with e_steps_per_unit set to mm of feedstock. | ||
+ | |||
+ | ===== Custom gcode files ===== | ||
+ | .skeinforge/ | ||
+ | < | ||
+ | |||
+ | .skeinforge/ | ||
+ | < | ||
+ | G90 | ||
+ | G1 X-250 Y-250 F4500 | ||
+ | G1 X-250 F4500 | ||
+ | G92 X0 | ||
+ | G1 X2 F800 | ||
+ | G1 X-10 F800 | ||
+ | G92 X0 | ||
+ | G1 Y-250 F4500 | ||
+ | G92 Y0 | ||
+ | G1 Y2 F800 | ||
+ | G1 Y-10 F800 | ||
+ | G92 Y0 | ||
+ | G1 Z-250 F60 | ||
+ | G92 Z0 | ||
+ | G1 Z1 F10 | ||
+ | G1 Z-10 F10 | ||
+ | G92 Z0</ | ||
+ | |||
+ | .skeinforge/ | ||
+ | |||
+ | < | ||
+ | G1 Z2 F30 | ||
+ | G1 X0 Y200 F4500 | ||
+ | G1 Z-250 F30 | ||
+ | G92 Z0</ | ||
+ | |||
+ | ===== SF ===== | ||
+ | Settings for plugins, as they appear in the interface. SF40, everything is in Craft tab. Settings are for PLA | ||
+ | |||
+ | ==== Bottom ==== | ||
+ | When Z axis homes its touching the plate to prevent oozing, so we have '' | ||
+ | |||
+ | ==== Carve ==== | ||
+ | Left to defaults | ||
+ | |||
+ | ==== Chamber ==== | ||
+ | Activated, '' | ||
+ | |||
+ | ==== Clip ==== | ||
+ | Active with defaults | ||
+ | |||
+ | ==== Comb ==== | ||
+ | Inactive | ||
+ | |||
+ | ==== Cool ==== | ||
+ | Active, '' | ||
+ | |||
+ | < | ||
+ | |||
+ | ==== Dimension ==== | ||
+ | Activated. '' | ||
+ | |||
+ | '' | ||
+ | |||
+ | ==== Export ==== | ||
+ | Deactivated '' | ||
+ | |||
+ | ==== Fill ==== | ||
+ | Active, with '' | ||
+ | |||
+ | ==== Fillet ==== | ||
+ | Inactive | ||
+ | |||
+ | ==== Home ==== | ||
+ | Activated, homing.gcode is used to read temperatue | ||
+ | |||
+ | ==== Hop ==== | ||
+ | Inactive | ||
+ | |||
+ | ==== Inset ==== | ||
+ | Active, at defaults | ||
+ | |||
+ | ==== Jitter ==== | ||
+ | Inactive | ||
+ | |||
+ | ==== Lash ==== | ||
+ | Inactive | ||
+ | |||
+ | ==== Limit ==== | ||
+ | Active, '' | ||
+ | |||
+ | Faster Z feed rate was giving funny results, as all objects were shrunk to 2/3 of expected size. Not sure about maximum initital feed rate setting. | ||
+ | |||
+ | ==== Multiply ==== | ||
+ | Activated, '' | ||
+ | |||
+ | This one moves objects to center of build plate. Quite important. | ||
+ | |||
+ | ==== Oozebane ==== | ||
+ | Inactive | ||
+ | |||
+ | ==== Preface ==== | ||
+ | At default values | ||
+ | |||
+ | ==== Raft ==== | ||
+ | Active, with '' | ||
+ | |||
+ | Rest at defaults. | ||
+ | |||
+ | ==== Scale ==== | ||
+ | Inactive | ||
+ | |||
+ | ==== Skirt ==== | ||
+ | Active, with '' | ||
+ | |||
+ | ==== Speed ==== | ||
+ | Active, with '' | ||
+ | |||
+ | This one slows down when printing outer layer, making prints prettier. | ||
+ | |||
+ | ==== Splodge ==== | ||
+ | Inactive | ||
+ | |||
+ | ==== Stretch ==== | ||
+ | Inactive | ||
+ | |||
+ | ==== Temperature ==== | ||
+ | Activated, but all temps set to 195 | ||
+ | |||
+ | ==== Tower, Unpause, Widen, Wipe ==== | ||
+ | Inactive | ||
+ | |||