Differences

This shows you the differences between two versions of the page.

--- project:weathersonde:telemetry_decoding [2014/02/20 13:29] – [Measurement subframe payload (0x69)] pinky
+++ project:weathersonde:telemetry_decoding [2017/02/18 21:59] – [Unknown subframe payload (0x68)] pinky
@@ Line 1: / Line 1: @@
+======= Telemetry decoding ======
+Describes how to decode data from [[telemetry_receiving|recieved telemetry]]. This includes evaluation of temperature, pressure and humidity from measured values or GPS coordinates.
+===== FRAME_PAYLOAD_DATA structure =====
+Each frame contains payload consisting of subframes with varying length.
+===== SUBFRAME structure =====
+^ offset (B) ^ lenght (B) ^ name ^ content ^
+| 0 | 1 | SUBFRAME_TYPE | Type of subframe ? |
+| 1 | 1 | SUBFRAME_LEN | Length of subframe payload |
+| 2 | 2*SUBFRAME_LEN | SUBFRAME_PAYLOAD | subframe payload |
+| 2*SUBFRAME_LEN+2 | 2 | SUBFRAME_CRC | CRC 16 of subframe payload, polynom = 0x11021 |
+==== Known subframe types ====
+^ SUBFRAME_TYPE ^ description ^
+| 0x65 | Calibration and Configuration fragment |
+| 0x69 | Measurement data |
+| 0x67 | GPS data |
+| 0x68 | RADAC (radiation measurement) / O3 (ozone) |
+| 0xff | padding ? |
+===== Calibration subframe payload (0x65) =====
+expected payload length: 32
+^ offset (B) ^ lenght (B) ^ name ^ content ^ description ^
+| 0 | 2 | CALIB_FR_NUM | uint16 | frame number, (starts from 1) |
+| 2 | 10 | CALIB_ID | string | 0x20 0x20 + sonde ID (same as on cover) |
+| 12 | 1 | CALIB_STATE_0 | uint8 | 0 - OK; 0x08/0x0A - battery low / battery low, powe off countdown running? |
+| 13 | 1 | CALIB_STATE_1 | uint8 | see table bellow |
+| 14 | 1 | CALIB_UNKNOWN_0 | 0x00 | ??? |
+| 15 | 1 | CALIB_FRAG_NUM | unit8 | callibration and configuration fragment number |
+| 16 | 16 | CALIB_FRAG_DATA | bytes | calibration and configuration data fragment |
+==== STATE_1 ====
+TODO: verification needed, possible documentation bug
+^ bit offset ^ description ^
+| (LSB) 0 | start detected (set at the same time as bit 5) |
+| 1 | ??? |
+| 2 | humidity sensor heating: 0 = off, 1 = on |
+| 3 | humidity sensor for measurement: 0 = U1 (CH2), 1 = U2 (CH3) |
+| 4 | set to 1 when current drown from battery is  increased by 50mA |
+| 5 | start detected (set at the same time as bit 1) |
+| 6 | ??? |
+| (MSB) 7 | ??? |
+===== Measurement subframe payload (0x69) =====
+expected payload length: 24
+^ offset (B) ^ lenght (B) ^ content ^ name ^ description ^
+| 0 | 3 | int24 | MEAS_T | Temperature sensor (wire at end of stick) |
+| 3 | 3 | int24 | MEAS_U1 | Humidity (remoter to sonde) |
+| 6 | 3 | int24 | MEAS_U2 | Humidity (closer to sonde) |
+| 9 | 3 | int24 | MEAS_REF1 | reference upper bound, increase with temperature (or vice versa, TODO) |
+| 12 | 3 | int24 | MEAS_REF2 | reference upper bound, decrease with temperature (or vice versa, TODO) |
+| 15 | 3 | int24 | MEAS_P | Pressure |
+| 18 | 3 | int24 | MEAS_REF3 | reference lower bound |
+| 21 | 3 | int24 | MEAS_REF4 | reference lower bound |
+<code>
+ref = (MEAS_REF3 + MEAS_REF4) / 2;
+p_rel = 1.0 / ((MEAS_P - ref) / (MEAS_REF1 - ref) - 0.0655) * 0.9053 + 0.08778;
+# pressure in hPa
+P = p_rel * ((((CALIB_COEFF[15] * p_rel + CALIB_COEFF[14]) * p_rel + CALIB_COEFF[13]) * p_rel + CALIB_COEFF[12]) * p_rel + CALIB_COEFF[11]) + CALIB_COEFF[10];
+ref4 = MEAS_REF2 - ref;
+u1_rel = 1.0 / ((MEAS_U1 - ref) / ref4);
+u2_rel = 1.0 / ((MEAS_U2 - ref) / ref4);
+# humidity
+U1 = (
+    (u1_rel * CALIB_COEFF[43] + CALIB_COEFF[42]) * \
+    u1_rel + CALIB_COEFF[41]) * u1_rel + ALIB_COEFF[40];
+U2 = (
+    (u2_rel * CALIB_COEFF[53] + CALIB_COEFF[52]) * \
+    u2_rel + CALIB_COEFF[51]) * u2_rel + CALIB_COEFF[50];
+U = max(U1, U2)
+rt = (1.0 / (CALIB_COEFF[37] - 1.0) + 17.99418) * \
+.079298 / (((MEAS_T - ref) / ref4) - 0.15791);
+# temperature °C
+T = ((((
+    rt * CALIB_COEFF[35] + \
+    CALIB_COEFF[34]) * rt + \
+    CALIB_COEFF[33]) * rt + \
+    CALIB_COEFF[32]) * rt + \
+    CALIB_COEFF[31]) * rt + \
+    CALIB_COEFF[30];
+</code>
+===== GPS subframe payload (0x67) =====
+expected payload length: 122
+^ offset (B) ^ lenght (B) ^ content ^ description ^
+| 0 | 4 | GPS_TIME (int32) | GPS time - ms from week start |
+| 4 | 2 | GPS_BLOB_0 | ???, 4*4 bits |
+| 6 | 8 | GPS_PRN | PRN for each tracked satelite |
+| 14 | 12 | GPS_STAT_1 | signal strength, fix status ...  |
+| 26 | 96 | GPS_DATA_1 | doppler, pseudorange, ... |
+=== GPS_PRN ===
+List of pseudorange sequence number for each recieving satelite, 0 == no satelite.
+*5 bit - PRN number (x - unused ?)
+  11100000 x2222211 44433333 x5555544 77766666 x8888877 AAA99999 xBBBBBAA
+=== GPS_STAT_1 ===
+GPS satelite channel state.
+^ offset (b) ^ length (b) ^ description ^
+| 0 | 4 (int4) | signal strength or fix quallity, 0xf == NaN / no signal |
+| 4 | 1 | time fix - set to 1 when time is succesfully obtained from subframe |
+| 5 | 1 | pseudorange fix ??? - pseudorange fix is correlated to time ? |
+| 6 | 1 | pseudorange fix ??? (not corelated to time ?) |
+| 7 | 1 | signal tracking - some signal found at certain frequency |
+=== GPS_DATA_1 ===
+^ offset (B) ^ length (B) ^ type ^ description ^
+| 0 | 4 | int32/fract32 ? | value in range < -2e6, 0x1400000 ), pseudorange in metters?, 0x7FFFxxxx == NAN |
+| 4 | 3 | int24/fract24 ? | some number, might be signed, not sure, doppler shift? |
+| 7 | 1 | ??? | number, min/max: < -38, 39 > usually -5..10 |
+===== RADAC / O3 (radiation and ozone measurement) (0x68) =====
+expected payload length: 10
+No usefull values available to decipher this frame, have someone something?
+^ offset (B) ^ length (B) ^ description ^
+| 0 | 10 | ??? |
+ussual content:
+x03 0x03 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
+===== Padding subframe (0xff) =====
+expected payload length: 4
+This type of frame probably identifies only padding
+  * no CRC?
+  * constant pattern of repeating (0x02 0x00) ?
+===== Configuration and calibration =====
+Calibration data are composed from fragments send in first subframe.
+Calibration data block is 512B long. Content is identical with data from EEPROM.
+- there should be somewhere date/time (GPS send only seconds offset from start of week)
+^ offset (B) ^ lenght (B) ^ content ^ description ^
+| 0 | 2 | ??? | ??? (checksum?) |
+| 2 | 2 | unit16 | downlik frequency: f = (400E6 + 10E3*value) Hz\\ upper limit is around 423MHz (value = 0x08FC) |
+| 4 | 2 | uint16 | always 0xffff - kill timmer ? |
+| 6 | 2 | int16 | always 0x0100 - set transmit power to full ? |
+| ??? |
+| 22 | 10 | string | probe ID (same as printed on conver, starts with 0x20 0x20) |
+| ??? |
+| 64 | 5*x | CALIB_COEFF | calibration coefficients table |
+==== CALIB_COEFF ====
+Consist of sequence of repeated fields with following structure:
+^ offset (B) ^ lenght (B) ^ context ^ description ^
+| 0 | 1 | uint8 | calibration constant index |
+| 4 | 4 | float32 | calibration constant value |
+Example of calibration data
+^ coefficient index row/col (x) ^ 0 ^ 1 ^ 2 ^ 3 ^ 4 ^ 5 ^ 6 ^ 7 ^
+^ 1x | -366.026 | -43.9063 | 393.234 | -131.314 | 25.6268 | -2.02341 |  | 0.96 |
+^ 2x | -803.34 | 363.815 | 317.784 | 127.429 |  |  |  | 0.96 |
+^ 3x | -187.802 | 89.6416 | -26.9122 | 9.15022 | -1.45707 | 0.0868068 |  | 0.849488 |
+^ 4x (humidity 1) | -1223.17 | 3548.18 | -2646.42 | 588.217 |  |  |  | 0.96 |
+^ 5x (humidity 2) | -1198.04 | 3497.31 | -2611.15 | 580.153 |  |  |  | 0.96 |
+^ 6x | 0.0318379 | 0.0374458 | -0.0433925  0.00630527 |
+^ 7x | -0.000132316 | 0.000414854 | -0.000402439 6.31402e-05 |
+^ 8x | -2.04505e-06 | 1.5662e-067.05777e-07 |
+^ 11x | 0.5227 | -0.0284 | 0.000286 | 8.97e-07 | -1.26e-09 |
+^ 12x | 1.07573 | -0.204 | 0.009009 | -5.83e-05 | -1.04e-06 |
+^ 13x | 0.5227 | -0.0284 | 0.000286 | 8.97e-07 | -1.26e-09 |
+^ 14x | 1.07573 | -0.204 | 0.009009 | -5.83e-05 | -1.04e-06 |
+^ 15x |  | 4.75029e-06-5.47494e-08   4.851e-10  -1.736e-12 | | | | | | 0.7 |
+^ 16x | |  |  |  |  |  |  | 0.7 |
+  * Coefficients at rows 1Nx are never chenge.
+==== related links ====
+  * [[http://ams.confex.com/ams/pdfpapers/69226.pdf]]